VAN PI DOCUMENTATION
  • VAN PI DOCS OVERVIEW
  • German Docs Version
  • 💫GET STARTED
    • FLASH VAN PI OS
    • Build your VAN PI CORE
    • First Start
      • Userinterfaces Overview
  • ➕Connecting devices
    • Watersensors
      • Resistance (Ohm)
      • Capacitiv (V)
    • Loads via relays
    • Signal Inputs
      • Input ALL OFF Funktionen
    • VAN PI DIMMY - LED Controller WIRED
    • Temperature Sensors
    • Setting up or moving temperature sensor
  • 🛜Wirelesss and Network
    • Network Config Overview
    • Wifi Settings
    • Bluetooth Devices
      • Ruuvi Tags
      • Pekaway MPPT S20
      • Senso4s Gok
      • Battery BMS
    • Time Sync
    • Victron Ve.Direct
    • Zigbee
  • 🪫ENERGY MANAGEMENT
    • Battery Monitoring
      • Pekaway Wireless Shunt
      • Bluetooth BMS Batterie
      • Victron Smart Shunt
    • Solar Controller
      • Pekaway MPPT S20
      • Victron
      • Votronic Solar
  • Remote Connection
    • Pekaway App
    • Pekaway LTE Bridge 4G
      • LTE BRIDGE UPDATE
    • LTE Router
    • Telegram
    • Apple Homekit - Homebridge
    • other
  • Position
    • RJ45 UART GPS
    • USB GPS
    • Pekaway 4G Bridge
    • orientation sensor
  • 🌡️heater
    • Autoterm 2D & 4D
    • Webasto
    • Truma
    • Chinese Diesel heater
  • API
    • MQTT
    • HTTP
  • DISPLAYs
    • RJ45 UART - Pekaway Touchdisplay
    • Tablets
    • Pekaway Android 5,5"
    • Sonoff NS PANEL
    • Button PLUS
    • HDMI
  • OTHER SOFTWARE STACKS
    • Home Assistant connector
    • NomadPI
  • DEBUG
    • I2C
    • Waterlevel
    • Network
Powered by GitBook
On this page
  1. ENERGY MANAGEMENT
  2. Battery Monitoring

Pekaway Wireless Shunt

PreviousBattery MonitoringNextBluetooth BMS Batterie

Last updated 9 months ago

Adding the Pekaway Wireless Shunt to the VAN PI OS is straightforward and user-friendly. The shunt, based on the ESP32-C3 microcontroller and you find the OpenSource Software for it on GITHUB. The shunt transmits the data via Bluetooth Low Energy (BLE).

To set it up, follow these simple steps:

  1. Navigate to the web interface.

  2. Go to Wireless -> Pekaway Wireless Shunt.

  3. Start the BLE scan.

The system will find the shunt and display it in the list. Once added, the shunt will begin transmitting data to the system.

For the initial setup of the shunt, you need to restart it to enter configuration mode, indicated by a blue LED light. During this mode, you will need to set the amp hours (Ah) of your battery and the current state of charge (SoC). The optimal setup involves charging your battery to 100% and then calibrating the shunt to reflect a full charge.

With these steps, your Pekaway Wireless Shunt will be successfully integrated into the VAN PI OS, providing you with accurate battery data.

If you want it to use the shunt as you primary battery Information, set "MAIN BATT DATA" to Pekaway Wireless Shunt.

RESET/Restart - Call up the configuration mode: Option 1: Connecting the 12V input voltage Option 2: Press the reset button:

UPDATE:

You can easily update the Wireless Shunt by connecting it to your PC and using Chrome or Edge to flash the new firmware.

🪫
http://flashesp.pekway.deflashesp.pekway.de